气动离合器是以压缩空气为操纵动力源的摩擦离合器。一般用于需要传递大转矩和以较快速度变换回转方向的设备上，如石油钻井机械、船舶、大型机械压力机、挖掘机、球磨机、橡塑机械等。 The spirit moves the clutch with compressed air for friction clutch that manipulate the motive source.Used for needing to be delivered the big torque generally with turn round the directional equipments with the fast a transformation last, such as the petroleum artesian well machine, ships, large machine pressure machine, scoop out the machine, ball whet machine, rubber machine etc..

气胎离合器传递转矩大，接合平稳，便于安装，吸振，能补偿少量主、从动轴角向和径向相对偏移，从动部分惯性小，使用寿命长，结构紧凑，密封性好。气胎变形阻力大，气胎材料成本高，使用温度有一定限制，高于60℃时会降低气胎寿命，低于-20℃时易使气胎变脆。气动离合器接合元件主要采用摩擦片、摩擦块等。 The Pneumatic tube clutch delivers to torque big, join together steady, easy to install, the absorb librate, can compensate a little amount lord, from move the stalk Cape face with path face opposite be partial to move, from move part inertial and small, service life long, construction tightly packed, seal completely sex good.The Pneumatic transforms the resistance big, the Pneumatic material cost is high, usage temperature contain certain restrict, higher than 60 ℃ will lower the Pneumatic life span, lower than-20 ℃ make the Pneumatic change the frailty easily.The spirit moves the clutch coalescence a main adoption rubs slice, rub an etc..

胎式离合器依据其结构形式的不同又可分为普通型与通风型两种。

Pneumatic type clutch according to its construction form of different can is divided into the common type again is two kinds of with well ventilated type.

1） 普通型common type

靠气胎传递扭矩，结构简单，制造、安装技术要求低，散热条件不如通风型，气胎容积较大，充气、放气时间较长，容易打滑。

Depending the Pneumatic delivers to torque, the construction is simple, make and installing the technique request to be low, thermolysis would be better to not as good as ventilated type, the Pneumatic capacity is bigger, the aeration and deflate time longer, easy is slippery.

2） 通风型Ventilated type

针对普通型不足之处而发展起来的一种气离合器，在结构上增加了一套散热传能装置。

Aim at the not enough an a kind of spirit for but developping clutch in common type, increased on the construction a set of spread the heat spread it can equip.

普通型气胎离合器Common type Pneumatic tube clutch

型号 type		LT300/100	LT500/125	LT600/125	LT700/200	LT700/135CBC	LT800/135
图号 drawing		115.101.00	115.102.00	115.105.00	115.103.00	115.107.00	T14-013-00
转速 rotata speed r/min	极限 max	2332－2667	1642－1877	1352－1547	1315－1504	1198-1450	1099-1328
	额定 rating	1348－1542	949－1085	781－894	760－869	687－881	635-768
扭矩 torsional moment N·m	极限 max	3080 -4030	10455 -13670	14810 -19360	33080 -43270	22350 -32660	28850 -42160
	额定 rating	2025 -2686	6970 -9114	9875 -12908	22060 -28850	14900 -21775	19230 -28080
工作压力 working pressure MPa		0.7－0.9	0.7－0.9	0.7－0.9	0.7－0.9	0.7－1.0	0.7-1.0
气胎容积 pneumatic tube cubage L		1.3	5.5	5.5	17	2-4	2.4-5
磨擦轮直径 attrition annulus dia. mm		Ф296	Ф497	Ф597	Ф695	Ф696	Ф796
联接  尺寸 join link size	轮缘直径 max dia.	Ф450	Ф720	Ф820	Ф1000	Ф900	Ф1015
	轮缘宽度 max width	115	154	154	246	176	176
	定位直径 orientation dia.	Ф450h11	Ф720 h11	Ф820 h11	Ф1000 h11	Ф900 h11	Ф1015 h11
	螺孔数量 及直径 bolt number and dia.	12-Ф13H12	12-Ф17 H12	16-Ф17 H12	12-Ф27 H12 4-Ф25H8	20-Ф17 H12	18-Ф17 H12 6-Ф17+0.043
	螺栓分布直径 bolt distributing dia.	Ф430	Ф690	Ф790	Ф950	Ф870	Ф975
进气管螺纹 air inlet pipe screw thread		M20×1.5	M20×1.5	M20×1.5	M33×1.5	2-M20×1.5	2-M20×1.5

通风型气胎离合器Ventilated type Pneumatic tube clutch

型 号type		AVB500/200	LT500/250T	AVB600/250	LT700/250T	LT700/135DY	LT800/250T
图 号drawing		G301.21.00	T14-014-00	G301.22.00	AF24001.02.0 1.00A	115.31.00	115.28.00
转速n rotata speed r/min	极限max	1312-1578	1586-1701	1281-1544	-	1569-1890	1016-1224
	额定rating	758-912	916-983	740-892	-	907-1092	587-707
扭矩M torsional moment N·m	极限max	17110-24970	23390-26900	32200-46710	-	24560-35630	54240-78660
	额定rating	11406-16646	15590-17930	21466-31140	32100-47300	16170-23750	36160-52440
工作压力 working pressure MPa		0.7－1.0	0.7－0.8	0.7－1.0	0.7－1.0	0.7－1.0	0.7－1.0
气胎容积 pneumatic tube cubage L		13×2	3-5	2×2	2.28×2	24	2.66×2
磨擦轮直径 attritio annulus dia. mm		Ф496	Ф496	Ф596	Ф696	Ф696	Ф796
联接 尺寸join link size	轮缘直径 max dia.	Ф780	Ф750	Ф890	Ф1010	Ф935	Ф1115
	轮缘宽度 max width	234	288	284	292	200	300
	定位直径orientation dia.	Ф300H8 40H8*80	Ф750f9	Ф340H8 40H8*100	Ф240+0.072	Ф360H10	Ф1105f9
	螺孔数量及直径bolt number and dia.	10-Ф18 H10	12-Ф18 H10	12-Ф23 H10	8-Ф32 H10	16-Ф22H10	16-Ф22 H10
	螺栓分布直径bolt distributing dia.	Ф360	Ф720	Ф420	Ф300	Ф400	Ф1070
进气管螺纹 air inlet pipe screw thread		2-G1/2 ”	2-M20×1.5	2-G1/2 ”	2-G1/2 ”	1-M20×1.5	2-G1/2 ”

通风型气胎离合器（续表）

Ventilated type Pneumatic tube clutch (Continue)

型 号type		LT800/250T	LT900/250T	LT1070/200T	AVB1120/300	LT1170/250T	AVB1250/300
图 号drawing		115.29.00	ZB01.05.00	115.01.00	G301.25.00	115.02.00	G301.26.00
转速n  rotata speed r/min	极限max	1016-1224	903~1087	932－1123	-	765－820	-
	额定rating	587-707	522~628	539－668	-	442－474	-
扭矩M torsional moment N·m	极限max	54240-78660	68000~98930	84600-122670	-	117740 -134130	-
	额定rating	36160-52440	45467~65953	56400-81790	123000 -175500	78490-89420	153000 -218000
工作压力 working pressure MPa		0.7－1.0	0.7~1.0	0.7－1.0	0.7－1.0	0.7－0.8	0.7－1.0
气胎容积 pneumatic tube cubage L		2.66×2	3×2	30	3.96×2	5-7	44×2
磨擦轮直径mm		Ф796	Ф897	Ф1065	Ф1116	Ф1166	Ф1246
联接尺寸 join link size	轮缘直径 max dia.	Ф1115	Ф1230	Ф1400	Ф1450	Ф1500	Ф1580
	轮缘宽度 max width	300	292	260	357	302	357
	定位直径orientation dia.	φ350H8 40H8×100	Ф1220-0.42	Ф1400h11	Ф840H8 60H8*100	Ф1500h10	Ф1050H8 60 H8*90
	螺孔数量 及直径 bolt number and dia.	12—φ22H10	16~Ф22 H10	12-Ф27 H10 4-Ф25H8	20-Ф23 H10	12-Ф27 H10	16-Ф25 H10
	螺栓孔分布直径 bolt distributing       dia.	φ420H8	Ф1184	Ф1350	Ф890	Ф1445	Ф1110
进气管螺纹 air inlet pipe screw thread		2-G1/2 ”	2-G1/2 ”	2-M33×1.5	2-G1/2 ”	2-M33×1.5	2-G1/2 ”

| 上一页 | 石油机械 | 冶金机械 | 制桶机械 | 下一页 |